Looking for staff pick simulation templates? Sign up for SimScale and join the largest engineering simulation community in the world! | Page 2

Engineering study of solar panels, including:

1. Wind loading and static structural analysis of a single panel

2. Transient wind analysis of a panel array

Analyse the duct positioning to have effective ventilation system

HVAC Design Project with open windows to understand how the air might flow through the buildings

Internal CFD study of air flow and thermal comfort.

Temperature distribution through a U-type heat exchanger.

Internal CFD to analyse air flow and thermal comfort

The aim of this project is to showcase how SimScale Platform could be used to perform CFD Analysis to optimize cooling cost of a Data Center.

A small part of the SimScale office . We actually don't have any active cooling here (Germany) so we took a few liberties to make this more interesting!

Contamination propagation Internal/External

An air flow bench is a device used for testing the internal aerodynamic qualities of an engine component and is used primarily for testing the intake and exhaust ports of cylinder heads of internal combustion engines, but the cost of flow bench is very high and thus, with the advent in computational simulation technology the port flow simulation can be conducted very easily to analyse the breathing capacity of the engine.

The undertray is known to be the most aerodynamically efficient downforce generating device. Theoretically, almost 50-60 percentage of the downforce generated by the aerodynamic package of an F1 car is generated by the undertray. Moreover, the undertray produces a very minimal amount of drag force owing to its reduced frontal area hence the lift(here downforce) to drag ratio is very high. Therefore, optimizing the undertray design is of great significance to the overall downforce generated by a car.

Project to analyse and optimise a Water Turbine (Frances Turbine).

This validation focuses on validating the moment coefficients using experimental results obtained by RWDI in their wind tunnel tests, published in the paper (Calin Dragoiescu, Jason Garber and Suresh Kumar, 2006) where results were published using two techniques, a high-frequency force balance (HFFB) and high-frequency pressure integration (HFPI) which uses tap points. Both showing mostly good agreement between the two, with HFFB expected to be more accurate.

Millions of people in the world live without clean water and access to basic sanitary facilities. The majority are based in isolated rural areas and spend hours every day walking to collect water for their family.

This not only keeps children out of school or take up time that parents could be using to earn a living, but the water often carries diseases. These diseases develop and spread due to inadequate sanitation and hygiene, particularly through toilets. For reasons of groundwater protection, the flushing and disposal of waste must be carried out without the use of water.

Ap project which analyses and improves a basic industrial blower system, the system is designed to extract a space in a working environment.

The objectives are to sequentially optimise the impeller and case design using the results of the previous iterations and to then gain the performance curves and understand how cavitation might affect the design.

Large Structure- Static Structural Analysis

To analyse, and optimise the heating of a residential block using various heating methods.

Using CFD to predicate pressure loss and improve HVAC design sequentially using CFD results.

This work aims to present the use of FEM in the analysis and design of an auxiliary device for the torque of the piston fixing nuts in hydraulic cylinders.

To validate CFD results against the Architectural Institute of Japan's Case F results both from the field and wind tunnel,

This project is intended towards validating the performance of a generic propeller geometry. Such a validation project enables the user to enhance their knowledge in leveraging CFD for modelling the performance of an existing drone or estimating the design parameters such as motor size, material property requirements, etc. during the development phase of a drone.

Case covered in the Academics Week of Mechanical Engineering - SAEM2018, Brazil. https://saem.unifesspa.edu.br/

Ventilation design for better Contaminant Fume extraction

This project intends to demonstrate a possible failure in the sterile waste pile dam of an iron mine with a real topography of the Gelado's Dam region, located in Carajás, Brazil.

Test of Feature refinement and as to whether anyone can add a 'Staff Pick' tag

The purpose of this project is to use experimental results from the Architectural Institute of Japan to validate CFD results gained from SimScale. The case being validated is Case E, which consists a complex of buildings with simplified geometry. Many scenarios are presented in Case E, The scenarios used to validate the SimScale platform were the North, East, South and Westerly winds for the after construction scenario.

The SimScale CFD results were compared to the experimental results and found to have good correlation. Some underprediction was seen in the k-epsilon models in the strong wind regions and underprediction in the wake regions, but is a known trait of the K-epsilon model and is acceptable and should be considered when evaluating results.

The purpose of this project is to use experimental results from the Architectural Institute of Japan to validate CFD results gained from SimScale. The case being validated is Case D, which consists of a single high-rise building, surrounded by blocks of simplified buildings. The geometry used was the scaled geometry from the data file provided by the Architectural Institute of Japan, and measurements were taken at points also listed in the data file.

This is the project presented in the SimScale webinar 'Thermal Comfort Assessment for ASHRAE 55 with CFD':
https://www.simscale.com/webinars-workshops/thermal-comfort-ashrae-55/

In this project we are interested in designing the HVAC outlets for a big theater room to improve the thermal comfort of the occupants inside.

Temperature Reduction and Energy Saving for Data Centers
In this webinar, you will learn how CFD can help you analyze data center designs and ensure energy efficiency for different standards

Profile thermal of the steel landle of the steelwork

This project establish a comparison between 120mm and 130mm EBT valve.

This is a theoretical and practical tutorial introducing the concept and implementation of Remote Point Boundary Conditions, both for degrees of freedom restriction and load application. It features a number of illustrative simulations and a companion commentary post for all the explanation.

The aim is to dimension the mast of a light pole of 11 meters high with variable diameters. The implementation of the project will be in the patio of Raízen in Marabá-BR, located on the railroad.

The cooling mechanism is very crucial to ensure the rated performance of CPU, at the same time it accounts for the major operating cost of the system. Therefore, an efficient electronics cooling is necessary to provide the continuous operations at low operating costs. Tools of computational Fluid Dynamics are widely being used to optimize the cooling mechanism of the chips. In this study the focus is on finding the optimum heat sink design for electronics cooling.

The purpose of this project is to validate the accuracy of the solver for transport and distribution of Gas (passive scalar) in an indoor environment.The airflow pattern (velocity) and concentration results from CFD are to be compared with experimental data obtained from full-scale tests.

staff pick | SimScale Project Library | Page 2