Looking for flow analysis simulation templates? Sign up for SimScale and join the largest engineering simulation community in the world! | Page 2

Simulate flow characteristics of supersonic nozzle at sea level and 15 km above sea level

TO DETERMINE THE EXACT SIZE AND BY USED OF CFD. IT IS USED FOR MEDICAL PURPOSES SINCE DUE TO COVID 19 PANDEMIC SO TO BE ABLE TO DESIGN A SUFFICIENT SIZE OF VVAVLVE

Water inlet for facility in use for pump water underground.

In this project incompressible fluid flow simulation of a conical draft tube is carried out. The parameters data is collected from the course book on fluid dynamics and the validation of CFD simulation result with the theoretical result is also performed. Steady state incompressible fluid flow simulation is selected for the given case.
The draft tube is a pipe of gradually increasing area, which connects the outlet of the water turbine's runner to the tail race. Draft tube helps to convert the exit velocity head into pressure or potential head.

Structural Stability and Lift generation of a box wing

The model was designed by one of my friends who is currently working on a DIY RC plane project. 
He was originally designing a simple glider before revising the design in order to make it a flying boat.

I was asked to analyse the flow around the aeroplane and here it is!
I reckon it still needs more fine tunings (geometry, meshing, sim control, etc.) but I'm chuffed to acheive a decent results.

From Prandtl's 1933 paper on Bell lift distribution for minimizing the induced drag and recent works being published by NASA on PRANDTL D glider,  I decided to do a performance study and comparison of this type of lift distribution along with the conventional elliptic lift distribution,  that is to compare two wings with different lift distributions but with the same plan form area, taper ratio and aspect ratio

flow around a square cylinder with Re 21400 and D 4 cm

Server rooms house sensitive hardware that can be damaged easily if exposed to extreme temperatures. So, the aim of this project is to find out the heat transfer in that room for material air. For heat transfer I did Conjugate Heat Transfer simulation analysis which tells us about the heat transfer between fluid air and the solid material of the server room.
So, from this project we can optimize the ventilation system design for server room in future planning.

Flowing liquid through a manifold assembly

This project deals with simulating the flow through the graphic card at different fan Rpms using the Multiple reference frame(MRF) rotational zone concept. A conjugate heat transfer analysis will be performed to keep a check on thermal throttling of the GPU.

DETERMINE ENERGY LOSSES IN A CLOSED LOOP PIPE

The goal is to investigate the behavior of an one-hour-design 3D printed glider while it gets actually printed.

116 minutes remaining before the wing sections are printed. Fin and fuselage still needs to be manufactured.
Hopefully some useful information will be acquired from this steady state incompressible CFD simulation before the hardware is all ready.
What is the speed range this plane can operate. Will this plane actually fly or it will be just a demo piece.

The glider is designed by some rules of thumb. 

Progress in the comments below!

Fan efficiency analysis of Notebook heat extraction system
(Incompressible flow simulation)

Determination of the flow field and temperature field in the area of the mixing region using Fluid Flow

In this study, the flow coefficient (K_v value) of a globe valve was calculated.

Analizar los vórtices causados  por un  tubo de PVC. Se usara una simulación de flujo.

A chemically reacting fluid flows through a channel.Design considerations require that the flow area of the duct be abruptly
reduced to 1/10th of its size. To prevent destruction of the duct by the reacting fluid,no stagnant eddies at the contraction can be allowed.have some control over the duct length upstream of the contraction, and thus the velocity profile of the fluid approaching the contraction. To solve this problem, you must somehow
estimate the flow field near the contraction.

Intake on my V6 design, Comparing Symmetric and Asymmetric.

Evaluation of air flow passing into a divergent duct, in funcion of its different geometry

Air flux in a divergent duct, simulating the air flux going from a fan to a radiator

HPAC Webinar-Duct Flow Analysis and Design Optimization

This project simulates instantaneous turbulent wake of a cylinder body via LES method.

This project simulates flow in a mixing-diffuser for juice flushing.

This project simulates flow of water through a spillway.

Flow analysis of an automotive carburetor

In this application, oxygen shall be mixed with water homogeneously. Therefore a static mixer design is analyzed regarding its mixing performance vs. the resulting pressure drop.

A turbulent flow simulation of a butterfly valve is demonstrated in this project.

simulating the flowfield around a sphere at supersonic speed

This project shows an example of how the internal airflow through an naca duct can be analyzed.

flow analysis | SimScale Project Library | Page 2