SimScale simulation projects by jousefm | Page 1

jousefm's profile

Validation of the performance of a centrifugal pump with the Subsonic analysis type, automatic pump curve generation and transient analysis. - Copy

This project simulates air flow around an Aircraft at low sub-sonic compressible flow regime. - Copy

The objectives are to analyse the pump's design and obtain enough information about it to create a pump curve characteristic.

Two different designs of a pipe junction are analyzed regarding their downstream behavior.

Project file for the course - ''An Introduction to FEA with SimScale'' - courses.jousefmurad.com

flow meter designed by 3DGoodPrints, a French based 3D service

Design of an enclosure capable of handling 100W components inside. Looking at heat sink design and fan selection

Webinar: Thermal Analysis of Passive Cooling for LED Systems

Flow Analysis of Exhaust Gas Flow Through Turbine

The cooling of a dense packaging of electronics (about 100W) inside an enclosure is simulated.

Data center cooling showing hot aisle heat removal

In this project, a thermal shock analysis of a globe valve is performed along with a flow analysis and a structural analysis

LED Spotlight project, aiming a bring the temperature of the diodes of a LED spotlight design below the maximum allowed temperature of 100C.

CFD optimisation with SimScale of an oven blower and heat exchanger led to a 30 percent increase in efficiency to the airflow (reduced pressure drop) and a 50 percent increase in thermal efficiency in the heat exchanger.

Objective: Analyse peak stresses and deformations under operational bearing forces

Enclosure for an industrial application of a GPU on the edge, cooled via an active fan from the top.

Building Information Modeling (BIM) is the foundation of digital transformation in the architecture, engineering, and construction (AEC) industry.

Cover is offset by 0.005 meter, 2 snaps, 
Assumptions : Symmetric on both planes.
Only a quarter portion of enclosure is analysed.

Conjugate heat transfer simulation to analyse the thermal performance of water cooled transistors.

This project shows the bending of an Aluminium pipe through rolling process.

Tutorial on incompressible flow simulation for aerodynamics studies, using SimScale Standard mesh algorighm.

This tutorial project aims to showcase how to set up and run a simulation for a pump geometry. The Standard meshing tool was used.

This project demonstrates the static stress analysis of three aircraft engine bearing bracket models considering both linear and nonlinear material definition. The models are tested with horizontal and vertical loading conditions as provided on the challenge page of GrabCAD.

Template for the convergence study course in Coursera

This study aims at validating the CHT v2 solver of SimScale GmbH. A peer-reviewed publication focussing on thermal analyses and cooling of an RF electronics package has been used as basis for this validation case:
(Reasonable assumptions and approximations have been made to bridge uncertainty in the publication). The validation study involves qualitative and quantitative comparisons of the CHTv2 solver with the commercial CFD code: FloTHERM.

Drone propeller flow analysis simulation using MRF model and SimScale standard mesher.

Design study of a passively cooled LED module to inform heat sink material selection

In this SimScale project, inspired by this article on cooling effectiveness, a CFD thermal analysis is used to predict the temperature of 30 commercial Li-ion 18650 cells under multiple casing designs and inlet flow conditions. The goal is to find the minimum cooling power so that the cells are kept below 40C.

Thermische Simulation eines Gehäuses mit Elektronikkomponenten.

Simulation of aerosols transmitted in a bus as a result of a human cough

Aim:
This project demonstrates the validity of the CHTv2 solver. through a Conjugate Heat Transfer (CHT) analysis  of a battery pack.
 
Validation Experiment Reference:
A peer-reviewed publication on battery pack thermal validation  has been used as basis for this study: 
https://www.mdpi.com/1996-1073/10/8/1157
(Reasonable assumptions and approximations have been made to bridge uncertainty in the publication)

The study compares local temperatures at available thermocouple locations from

Validation Case for the Coursera course on engineering simulation.

In this project a static analysis of an I-beam under remote force is demonstrated.

Status: Public.

Updated geometries for the section Incompressible Fluid Flow analysis of two globe valves of the Introduction to Computer-Aided Engineering (CAE) course - www.simscale-academy.com

Public Profile

jousefm's profile